BITUTHENE® post-applied waterproofing
Proven Performance from the World’s Most Trusted Post-applied Waterproofing Membrane.
A time-tested, field-proven product.
Plazas and parking decks. Inverted roofs, green roofs and elevated decks. Basement walls. Tunnels, metro stations and infrastructure products. For each of these applications and more, there’s a BITUTHENE® product developed by GCP. BITUTHENE® is the most trusted post-applied waterproofing membranes. Its effectiveness has been proven time and again in countless projects. Long lasting, versatile and easy to install, BITUTHENE® gets the job done.
BITUTHENE® Product Documents
Products
Bituthene® 4000/4000S is a flexible waterproof membrane combining a high performance cross laminated, HDPE carrier film with a unique super sticky self-adhesive rubber bitumen compound.
- Cold applied
- Suitable for application to “green” concrete
- Moisture tolerant primer system
- Wide application temperature range
BITUTHENE® 5000, also known as Heavy Duty BITUTHENE®, is a waterproofing material incorporating high strength, heat resistant mesh embedded in a layer of self-adhesive rubberised asphalt.
- Cold applied
- Flexible
- Robust
- Pre-formed
- Slab drainage and joints
- Kerb and termination edges
BITUTHENE® 8000/8000S membranes combine the proven BITUTHENE® adhesive technology with a unique, grey coloured carrier film to provide superior performance and easier installation.
- Water and vapour proof – provides protection for basements, BS 8102:2009.
- Gas resistance – BITUTHENE® 8000 and 8000S membranes are certified by BBA to score 2 points as a gas resistant barrier (see BS 8485-2015+A1-2019, Table 7).
- Chemically resistant – provides effective external protection against most aggressive soils, contaminated ground water and hydrocarbons in suspension.
Bituthene® GP is a combination of a high density polyethylene film and a self-adhesive rubber/bitumen compound. It is supplied in rolls 1 mm thick overall, 1 m wide and 25 m long (25 m2).
- Waterproof
- Cold applied
- Flexible
- Reduces installation risk
Low-risk applications only
BITUTHENE ® LM (E) detailing compound is designed to complement GCP sheet membranes and systems.
- Liquid applied – conforms to irregular profiles
- Waterproof – resistant to water vapour and water pressure
- Tough rubber-like – flexible and damage resistant
- Seamless – joint free membrane
- Pile head terminations
- Terminations into DPC
- Pipe and rod penetrations
- Membrane continuity through masonry
BITUTHENE® Mastic is a cold applied one part solvent based bituminous mastic used to seal BITUTHENE® membranes when terminated in concrete chases or in raked mortar joints in masonry.
- No mixing necessary
- Simple application
- Designed to complement the range of BITUTHENE® waterproofing systems and assists with the application by solving small detailing problems.
BITUTHENE®MRX is a methane, carbon dioxide and radon resistant grade of BITUTHENE®specifically designed to resist these harmful gases.
- Resistant to passage of methane, carbon dioxide and radon gas
- Gas resistant
- Water and vapour proof
- Laminated metal foil/polymer
GCP Applied Technologies (“GCP”) BITUTHENE® Primer B1 is a solvent based bituminous primer used to prepare substrates where BITUTHENE® GP membranes are to be applied.
- Application at temperatures of +5 °C and above
- Specifically formulated to provide enhanced adhesion with BITUTHENE® GP membrane
- High coverage – Low cost per square metre
- Rapid drying
- Ideal for winter use
Suitable for use on masonry or wood surfaces
BITUTHENE® Primer S2 is a rubber-based primer in solvent, specially formulated to provide good initial adhesion.
- All temperature application above -5°C
- Green and damp concrete tolerant
- Quick drying
- Rubberised formulation
Used to prime “green” concrete or damp to touch substrates, as well as masonry or wood surfaces
BITUTHENE® Primer W2 is a water-based surface conditioner specifically formulated to prepare concrete, masonry and wood surfaces for the Systems.
- Application temperature above 0°C
- Damp concrete application
- Water Based
Suitable for use on damp to touch substrates, but it cannot be used to prime “green” concrete
Accessories
BITUTHENE ® LM (E) detailing compound is designed to complement GCP sheet membranes and systems.
- Liquid applied – conforms to irregular profiles
- Waterproof – resistant to water vapour and water pressure
- Tough rubber-like – flexible and damage resistant
- Seamless – joint free membrane
- Pile head terminations
- Terminations into DPC
- Pipe and rod penetrations
- Membrane continuity through masonry
GCP Applied Technologies (“GCP”) BITUTHENE® Primer B1 is a solvent based bituminous primer used to prepare substrates where BITUTHENE® GP membranes are to be applied.
- Application at temperatures of +5 °C and above
- Specifically formulated to provide enhanced adhesion with BITUTHENE® GP membrane
- High coverage – Low cost per square metre
- Rapid drying
- Ideal for winter use
Suitable for use on masonry or wood surfaces
Bituthene® Primer B2 is a rubber-based primer in solvent specially formulated to provide good initial adhesion of Bituthene® waterproofing membranes and GCP underlay. In addition, its patented formulation promotes the adhesion of Bituthene® membranes to green concrete and damp surfaces.
Accessory
BITUTHENE® Primer S2 is a rubber-based primer in solvent, specially formulated to provide good initial adhesion.
- All temperature application above -5°C
- Green and damp concrete tolerant
- Quick drying
- Rubberised formulation
Used to prime “green” concrete or damp to touch substrates, as well as masonry or wood surfaces
BITUTHENE® Primer W2 is a water-based surface conditioner specifically formulated to prepare concrete, masonry and wood surfaces for the Systems.
- Application temperature above 0°C
- Damp concrete application
- Water Based
Suitable for use on damp to touch substrates, but it cannot be used to prime “green” concrete
Products
- PRODUCT NAME
- DESCRIPTION
- KEY BENEFITS
- APPLICATIONS TYPE
Bituthene® 4000/4000S is a flexible waterproof membrane combining a high performance cross laminated, HDPE carrier film with a unique super sticky self-adhesive rubber bitumen compound.
- Cold applied
- Suitable for application to “green” concrete
- Moisture tolerant primer system
- Wide application temperature range
BITUTHENE® 5000, also known as Heavy Duty BITUTHENE®, is a waterproofing material incorporating high strength, heat resistant mesh embedded in a layer of self-adhesive rubberised asphalt.
- Cold applied
- Flexible
- Robust
- Pre-formed
- Slab drainage and joints
- Kerb and termination edges
BITUTHENE® 8000/8000S membranes combine the proven BITUTHENE® adhesive technology with a unique, grey coloured carrier film to provide superior performance and easier installation.
- Water and vapour proof – provides protection for basements, BS 8102:2009.
- Gas resistance – BITUTHENE® 8000 and 8000S membranes are certified by BBA to score 2 points as a gas resistant barrier (see BS 8485-2015+A1-2019, Table 7).
- Chemically resistant – provides effective external protection against most aggressive soils, contaminated ground water and hydrocarbons in suspension.
Bituthene® GP is a combination of a high density polyethylene film and a self-adhesive rubber/bitumen compound. It is supplied in rolls 1 mm thick overall, 1 m wide and 25 m long (25 m2).
- Waterproof
- Cold applied
- Flexible
- Reduces installation risk
Low-risk applications only
BITUTHENE ® LM (E) detailing compound is designed to complement GCP sheet membranes and systems.
- Liquid applied – conforms to irregular profiles
- Waterproof – resistant to water vapour and water pressure
- Tough rubber-like – flexible and damage resistant
- Seamless – joint free membrane
- Pile head terminations
- Terminations into DPC
- Pipe and rod penetrations
- Membrane continuity through masonry
BITUTHENE® Mastic is a cold applied one part solvent based bituminous mastic used to seal BITUTHENE® membranes when terminated in concrete chases or in raked mortar joints in masonry.
- No mixing necessary
- Simple application
- Designed to complement the range of BITUTHENE® waterproofing systems and assists with the application by solving small detailing problems.
BITUTHENE®MRX is a methane, carbon dioxide and radon resistant grade of BITUTHENE®specifically designed to resist these harmful gases.
- Resistant to passage of methane, carbon dioxide and radon gas
- Gas resistant
- Water and vapour proof
- Laminated metal foil/polymer
GCP Applied Technologies (“GCP”) BITUTHENE® Primer B1 is a solvent based bituminous primer used to prepare substrates where BITUTHENE® GP membranes are to be applied.
- Application at temperatures of +5 °C and above
- Specifically formulated to provide enhanced adhesion with BITUTHENE® GP membrane
- High coverage – Low cost per square metre
- Rapid drying
- Ideal for winter use
Suitable for use on masonry or wood surfaces
BITUTHENE® Primer S2 is a rubber-based primer in solvent, specially formulated to provide good initial adhesion.
- All temperature application above -5°C
- Green and damp concrete tolerant
- Quick drying
- Rubberised formulation
Used to prime “green” concrete or damp to touch substrates, as well as masonry or wood surfaces
BITUTHENE® Primer W2 is a water-based surface conditioner specifically formulated to prepare concrete, masonry and wood surfaces for the Systems.
- Application temperature above 0°C
- Damp concrete application
- Water Based
Suitable for use on damp to touch substrates, but it cannot be used to prime “green” concrete
Accessories
- ACCESSORY NAME
- DESCRIPTION
- KEY BENEFITS
- APPLICATIONS TYPE
BITUTHENE ® LM (E) detailing compound is designed to complement GCP sheet membranes and systems.
- Liquid applied – conforms to irregular profiles
- Waterproof – resistant to water vapour and water pressure
- Tough rubber-like – flexible and damage resistant
- Seamless – joint free membrane
- Pile head terminations
- Terminations into DPC
- Pipe and rod penetrations
- Membrane continuity through masonry
GCP Applied Technologies (“GCP”) BITUTHENE® Primer B1 is a solvent based bituminous primer used to prepare substrates where BITUTHENE® GP membranes are to be applied.
- Application at temperatures of +5 °C and above
- Specifically formulated to provide enhanced adhesion with BITUTHENE® GP membrane
- High coverage – Low cost per square metre
- Rapid drying
- Ideal for winter use
Suitable for use on masonry or wood surfaces
Bituthene® Primer B2 is a rubber-based primer in solvent specially formulated to provide good initial adhesion of Bituthene® waterproofing membranes and GCP underlay. In addition, its patented formulation promotes the adhesion of Bituthene® membranes to green concrete and damp surfaces.
Accessory
BITUTHENE® Primer S2 is a rubber-based primer in solvent, specially formulated to provide good initial adhesion.
- All temperature application above -5°C
- Green and damp concrete tolerant
- Quick drying
- Rubberised formulation
Used to prime “green” concrete or damp to touch substrates, as well as masonry or wood surfaces
BITUTHENE® Primer W2 is a water-based surface conditioner specifically formulated to prepare concrete, masonry and wood surfaces for the Systems.
- Application temperature above 0°C
- Damp concrete application
- Water Based
Suitable for use on damp to touch substrates, but it cannot be used to prime “green” concrete
Flexible and powerful
BITUTHENE® is available in a number of grades to suit your project needs. Supplied as an easily-applied sheet, It can be cold-applied at temperatures as low as 25°F, and can be placed on a variety of concrete surfaces. Its robust waterproofing properties, combined with its ease of application, results in a contractor-friendly product that adds value to buildings.
Apply easily, anywhere
Although the chemical properties of BITUTHENE® make it suitable for a variety of applications, we have added mechanical innovations to further its ease of use and long-term viability.
- RIPCORD® design lets workers easily split release liner for ease of positioning
- Cold-applied membrane avoids risk of fire during installation due to the fact that flame and/or hot works are not required
- Self-adhesive overlaps avoid leaky seams and eliminate the need for specialised equipment or training.
- When used with primer, BITUTHENE® can easily be applied to damp or green concrete during time-sensitive construction, saving time and money for the project team.
Unparalleled water protection
Buildings change and settle over time, but BITUTHENE® accommodates those changes.
- Robust film and specially formulated adhesive provide maximum water protection
- Flexible yet strong membrane provides crack bridging capabilities and moves with concrete, accommodating minor settling
- Controlled thickness ensures lack of variation
Get world-class technical services
With so many versatile applications, there’s a BITUTHENE® solution for nearly every project and design. We provides world-class technical services in order to make those limits even smaller.
